Motion Pro Tools

Wide blade screwdriver for removing caps crankcase.   Width blades: 16 - 22 - 38 mm

Interchangeable piston adapters Made of durable 6061 aluminum Fits all piston pins from 13 mm (0.511") to 24 mm (1 inch) Works on both full skirt and short skirt (slipper) pistons Non marring aluminum pin adapters Durable blue anodized finish with laser e

Kit includes a dial indicator with extensions and a 14 mm spark plug thread adapter Allows inspection and adjustment of ignition timing Scaled in millimeters Designed to clear frame tubes on most recent water cooled models Gauge face size 48mm Due to limi

Wheel bearing remover set with split collet adapters to move aside.   Simple and rapid, compatible with all types of bearings 6 adapters: Ø 10 - 12 - 15 - 17 - 20 - 25mm 2 driver adapters

Slot sockets Ø 47 mm for lock and unlock the slot nuts as locking ring nut of steering column.   Number of pins: 4 Ø 47 mm 3/8" square drive or wrench 22 mm Replaces Honda tools 07HMA-KS70100 07YMA-KZ40100 For wheel bearing/seal retainer ring: fits Hon

Slot sockets Ø 44 mm for lock and unlock the slot nuts as locking ring nut of steering column.   Number of pins: 4 Ø 44 mm 3/8" square drive or wrench 22 mm For wheel bearing/seal retainer ring: fits Honda CR125/250R 84-99 - CR500R 84-01

Slot sockets for lock and unlock the slot nuts as locking ring nut of steering column.   Number of pins: 4 Ø 37/47 mm For wheel bearing/seal retainer ring: fits Honda XR650L 93-07, XR600R 85-00, XR500 79-84, XR350R 83-85, XR250R 84-95, XR200R 81-02, XL2

Allows to change the swingarm bearings on most bikes.   Kits includes several driver sizes: ID 20 mm / OD 26 mm ID 21 mm / OD 26 mm ID 22 mm / OD 27 mm

The MOTION PRO carburettor synchronizer is mercury-free and is used to precisely synchronize carburetion parts.

4 adaptors 50mm + 4 reducer Designed for 890083  

Carburettor synchronizer with column for aligns and calibrates the vacuum in the ducts admissions.   Delivered complete with instructions, hoses and multiple connections 5 mm Remplacement fluid: 890087 Adaptors set brass Ø 5 mm: 890008 Adaptors set bras

Compatible with all KZ models.

Compatible with twin-cam models.

Flat slot for special carburator screwdriver, optimal for air/mixture setting, or for idle.

Standard clutch cable Direct replacement for OE Braiding and extra-tough materials for greater longevity Nylon sheath Cable ready to install

Standard throttle cable Direct replacement for OE Braiding and extra-tough materials for greater longevity Cable ready to install

Used to install a standard Mikuni idle adjuster into the carburetor body For use on Yamaha Banshee and Blaster models Idle adjuster is necessary if carburetor top has been replaced with a standard Mikuni cap Drill press or mill should be used to drill hol

Screw + nut Sold by unit

Aftermarket and OEM spec applications Standard type cap for most Mikuni VM 26-34mm carbs Generally used in throttle kits for Yamaha Banshee/Blaster

Protects the fork seal and wiper of inverted forks from damage by the bushing groove during installation Eliminates the need to wrap the fork tube with tape Set includes 36, 41, 43, 45, 46, 47, 48 and 49 mm bullets Fitment size is marked on each bullet fo